Sort by
Position
Name: A to Z
Name: Z to A
Price: Low to High
Price: High to Low
Created on
Display
100
per page
Replacement cell side secondary bracket for AK(U)-2-25 cells.
Maintenance handle for manually closing electrically operated breakers.
AK 2 25 breaker side secondary disconnect mounting bracket.
Replacement indicator tape for jackscrew type AKD 5 cells. 16 3/8" long metal with label.
Secondary disconnect mounting bracket to be used on the right hand side of AK 2A 25 circuit breakers.
Replacement indicator tape for jackscrew type AKD 5 cells. 17 7/8" long metal with label.
Flash barrier between arc chutes and secondaries on AK 50 breakers.
Grey molded plastic replacement handle for AK 50/75/100 manually operated circuit breakers.
T-Bolt used for arc chute retainer bar on AK 75 breakers.
Flash barrier between arc chutes and secondaries on AK 75 breakers.
Shielding the stationary contacts on an AK 75.
Lip style seal and gasket for AK 50-100 motor/gearbox assemblies.
Replacement bell alarm switch with two normally open contacts.
Molded body to replace molding on the top of relay that often breaks.
Used with ratchet to replace triangular style maintenance handle for AK 50-100 and AKR 75-100 circuit breakers.
Seven contact block with NPE's exclusive solid threaded contacts.
Replacement AK/AKR trip shaft bearing with groove.
Replacement AK/AKR trip shaft bearing without groove.
Solid contact with hardware and screw connection eliminates the need for crimped and soldered connections.
Normally open motor cut off switch for AK, AKR and Wavepro electrically operated circuit breakers.
Normally closed motor cut off switch for AK, AKR and Wavepro electrically operated circuit breakers.
Replacement padlock provision kit for AKD 10.
AKD 5 jackscrew cradle indicator roller replacement for AK 2A 50/75/100 and AKR A 30/50/75 breakers.
Replacement mechanism bushing kit for AKR 30/50 breakers.
Replacement AKR 30/50 rear barrier above top finger clusters
Arcing contact link for AKR 75/100 breakers
Round/rotary style auxiliary switch.
Replacement brass gear for AKR 75 and 100 racking gears.
Replacement brass gear for AKR 75 and 100 racking gears.
Replacement brass gear for AKR 75 and 100 racking gears.
Replacement racking interlock slide for AKR D 75/100 and AKR F 75/100 air circuit breakers.
Racking handle for removal and installation of breakers.
Replacement rubber bumper for AKR and AKRU 30/50 crossbars.
Replacement molded base to be used with existing contacts.
Complete new secondary with contacts springs and retainers.
Replacement shutters for AM 4.16-350 3000A cell. 2 per set.
Replacement solid steel stem caster for 5kv magneblast breakers.
Reconditioning service to align, seal and replace original "tar pitch' style potting material and buss insulation with modern material to eliminate cracking, leaking and misaligned connections that can cause catastrophic failures.
Arcing contact flash barrier made to be more durable than the original acrylic barrier that tends to crack and break.
Replacement brass bushing for ML-13 charging arm.
ML 13 bearing kits for rebuilding magneblast stored energy mechanisms.
ML 13 bushing kits for rebuilding and upgrading magneblast stored energy mechanisms.
Replacement for worn ML 13 prop bushings.
Motor coupler for Magneblast raise/lower motors.
Handle crank replacement for raise/lower motor, used to install or remove Magneblast breakers.
Cast style raise lower bushing kit for rebuilding Magneblast lift mechanisms.
Fabricated style raise lower bushing kit for rebuilding Magneblast lift mechanisms.
Aftermarket replacement 450 rpm motor for raising and lowering magneblast circuit breakers in cubicles.
Aftermarket replacement 450 rpm motor for raising and lowering magneblast circuit breakers in cubicles.
Aftermarket replacement 450 rpm motor for raising and lowering magneblast circuit breakers in cubicles.
Aftermarket replacement 450 rpm motor for raising and lowering magneblast circuit breakers in cubicles.
Base plate for newer style magneblast raise/lower motors.
Wire connector used on moving and stationary side of secondary disconnect for control wiring controls.
Slow close maintenance handle for AM 4.16 50 and AM 4.16 75 circuit breakers with MS-9 mechanisms.
Extension cord used for maintenance and testing outside of cell.
Used for removing and installing stationary contacts on GE AM breakers.
Eight contact block ruggedized to prevent cracks and damage. Contacts not included.
Eight contact block with NPE's exclusive solid threaded contacts.
Encapsulated replacement close coil for limitamp air contactors.
Encapsulated replacement close coil for limitamp air contactors.
Encapsulated replacement close coil for limitamp air contactors.
Encapsulated replacement close coil for limitamp air contactors.
Pole shader for use with Limitamp contactor armatures with AC coils.
Ground defeat cable used for testing GE MVT/SST type trip units.
Communications plugs with pins for General Electric MVT+ solid state trip systems.
Breaker side secondary disconnect block for GE AK equipped with Nelson drawout.
Spacer needed for converting older GE MVT base to accept RMS 9 or MVT+.
Replacement operating handle for 5 and 15 kv type SE 100S load break switches.
Replacement ground defeat cable.
Replacement indicator tape for VB or VB1 breakers. Metal with label.
Replacement handle for VB or VB1 charge handle.
Reinforced breaker side secondary disconnect block without contacts.
Reinforced cell side secondary disconnect block without contacts.
Tool used to remove contacts for VB/VB1 Secondary Disconnect Block.
Reinforced breaker side secondary disconnect block with 4 ft. of wiring harness.
Reinforced cell side secondary disconnect block with 8 ft. of wiring harness
Reinforced breaker side secondary disconnect block with contacts.
Reinforced cell side secondary disconnect block with contacts.
Contact used in VB/VB1 breaker side secondary block.
Contact used in VB/VB1 cell side secondary block.
VB/VB1 spring block for VB or VB1 closing spring.
Extension cord used for maintenance and testing of the breaker outside of the cell.
Newer style round auxiliary switch for VB1 circuit breakers.
Lifting assembly for use with overhead lift for removing and installing circuit breakers